In this guide
Key takeaways
- Settle daily watt-hours, worst-month sunlight and system voltage before choosing any part.
- Use an MPPT controller for anything beyond a small system, and keep the array's cold-weather Voc under its input limit.
- Size the battery for days of autonomy at a sensible depth of discharge, and plan for cold and ventilation.
- A main battery fuse, a fuse or breaker on every circuit, disconnects and correctly sized cable are not optional, and kits often skip them.
- Follow the NEC (Articles 690 and 706) as adopted locally, check permits, and use a licensed electrician where required.
A shed or cabin solar system is a set of parts that have to agree with each other: panels whose voltage suits the controller, a controller that knows how to charge your battery, a battery that can feed the inverter, and protection on every wire in between. Kits labeled "complete" often cover the first two or three and leave the rest to you, and the missing pieces are usually the safety parts. This checklist walks through each component in the order power flows, explains the one or two specs that matter for each, and ends with a master table you can shop from. It's written for a small to mid-size off-grid build: a backyard workshop, a hunting cabin, or a weekend place.
Before you buy anything: three decisions
Every part on this checklist depends on three numbers. Settle them first, and the shopping list almost writes itself.
- Daily energy (Wh/day)Multiply each device's wattage by its hours of use per day and add them up. That is the U.S. Department of Energy's formula. Include always-on loads and the inverter's idle draw. Our worked sizing example shows the whole process.
- Worst-month sunlightLook up monthly solar radiation for your location in NREL's PVWatts calculator, and size the array to the darkest month you'll actually use the building.
- System voltage12V suits small systems; 24V or 48V suits larger ones. Victron's Wiring Unlimited guide recommends raising system voltage before resorting to very thick cable, because the same power at double the voltage needs half the current.
With those settled, work through the parts below in order. Each section ends with what to confirm before you buy.
Panels and mounting
For a fixed shed or cabin, rigid monocrystalline panels are the usual choice: durable, easy to mount and simple to compare by their label specs. Flexible panels make sense mainly on curved surfaces where weight matters.
Write down three numbers from each panel's label or datasheet. You need them to match the charge controller:
- Voc (open-circuit voltage): the highest voltage the panel produces, which rises in cold weather
- Isc (short-circuit current): the most current it delivers
- Rated watts: output at the 1,000 W/m² reference level used for nameplate ratings
Mounting
Choose roof, pole or ground mounts based on sun exposure, not convenience. Shade from a single branch can cut output sharply. Tilt matters most in winter: PVWatts lets you compare tilt angles for your location before you commit. On a roof, use mounting hardware made for your roofing material and seal every penetration.
- Panel Voc, Isc and watts recorded for controller matching
- All panels in the same string have matching electrical specs
- Mount type suits the roof or ground, with an unshaded location
- Tilt chosen with your worst month in mind
Charge controller: MPPT vs PWM
The charge controller sits between the panels and the battery and keeps the battery from being overcharged. There are two types, and the choice matters more than its price suggests.
| PWM | MPPT | |
|---|---|---|
| How it works | Acts like a switch; pulls the panel voltage down to roughly battery voltage | Runs the panels at their most productive voltage and converts it to battery-charging current |
| Panel voltage | Must closely match the battery (e.g., "12V" panels on a 12V battery) | Can be much higher than battery voltage, so panels can be wired in series |
| Best for | Very small, low-cost systems | Anything beyond a few hundred watts, or cold or cloudy climates |
| Cost | Lower | Higher, but can reduce cable cost |
Victron Energy describes PWM as a low-cost solution for small systems only, and says MPPT is worthwhile once array power passes a few hundred watts on a 12V battery. It cites a 10–40% harvest advantage for MPPT under conditions like cooler cell temperatures (below 45°C) or very low light, which describes much of the year for a cabin in a temperate climate. For most shed and cabin builds, MPPT is the right call. More detail in our MPPT vs PWM comparison.
Matching the controller
- Max PV input voltage: the array's total Voc (panels in series add up) must stay below it, with headroom for cold mornings when Voc rises
- Rated output current: array watts ÷ battery voltage should fall comfortably within it
- Battery profiles: it must support your chemistry (LiFePO4, AGM, gel or flooded)
- Monitoring: a display or Bluetooth app makes troubleshooting far easier
Panel voltage rises as temperature falls, so a string that is fine in July can exceed the controller's input limit on a frigid January morning. Use the controller maker's sizing tool or the panel's temperature coefficient to check. See our guide to cold-weather Voc headroom.
Battery bank
The battery stores daytime energy for nights and cloudy days. For a shed or cabin you'll choose between lithium iron phosphate (LiFePO4) and lead-acid (flooded, AGM or gel). The full comparison is in our LiFePO4 vs lead-acid guide. For a checklist, the essentials are:
- Size: daily Wh × days of autonomy ÷ usable depth of discharge. Victron rates its LiFePO4 cycle life at 80% depth of discharge; Trojan generally recommends 20–50% for lead-acid, so lead-acid banks end up larger.
- Temperature: Battle Born says standard LiFePO4 shouldn't be charged below about 25°F without internal heating. Trojan notes lead-acid can freeze below 32°F if not fully charged. An unheated shed in a cold climate needs a heated battery, an insulated battery box, or a plan for winter.
- Ventilation: Trojan says to charge batteries in a properly ventilated area. Flooded batteries gas much more than AGM or gel. Never put flooded batteries in a sealed box inside a living space.
- Matching: buy batteries for a bank together, same model and age, and wire them per the manufacturer's instructions.
The National Electrical Code's Article 706 applies to energy storage systems with a capacity greater than 1 kWh. A single 12V 100Ah battery is about 1.28 kWh, so even a modest cabin bank can fall under it where the NEC is adopted.
Inverter
The inverter turns battery DC into the 120V AC your appliances expect. Three specs matter:
- Pure sine wave output. It is the safe choice for electronics, motors and chargers.
- Continuous rating. It must cover everything that runs at the same moment. Surge ratings cover only short bursts, such as a motor starting.
- Idle (no-load) draw. The inverter uses power whenever it's on. In a small system, that idle draw can be a big share of the daily budget.
If you want generator backup or shore power, consider an inverter-charger, which can also charge the battery from an AC source. Our inverter-charger vs standalone guide compares them. Some cabins run lights and a 12V fridge directly on DC and switch the inverter on only when needed, which saves its idle draw entirely.
- Input voltage matches your battery bank (12, 24 or 48V)
- Continuous watts cover your largest simultaneous load, with margin
- Pure sine wave output
- Idle draw known and included in your daily Wh
Fusing, disconnects and wiring
This is the section kits most often leave out and DIY builds most often get wrong. Batteries can deliver enormous current into a short circuit. Overcurrent protection exists to protect the wire from overheating, and every circuit needs it.
Fuses and breakers
- Main battery fuse: Victron's Wiring Unlimited guide says a DC system should always have a main fuse, placed in the positive cable. For LiFePO4 banks, a high-interrupt fuse type is common; see our Class T fuse guide.
- Branch circuits: each load circuit gets its own fuse or breaker. Per Victron, size it to the load, but never above what the cable can carry; if the cable is rated lower, the cable rating wins.
- PV and controller circuits: protect the controller-to-battery cable, and the array side as the controller and panel manufacturers specify.
Disconnects
You need a way to isolate the battery, the array and the inverter for service. Victron recommends isolating only the positive battery cable where battery isolation is needed, and using quality switches, because a poor switch adds resistance. Our breaker vs fuse vs disconnect guide explains the roles.
Wire and connections
- Size for current and distance. Victron advises aiming for no more than 2.5% voltage drop. Long panel runs and short, high-current battery-to-inverter runs both need careful sizing.
- Crimp properly. Victron recommends a professional ratcheting crimp tool, lugs matched to the cable size, and a tug test after every crimp.
- Use proper PV connectors and outdoor-rated cable on the array side, and cable glands where wires enter the building.
DC from panels and batteries can cause serious burns, fires and shocks. Panels produce voltage whenever light hits them. Cover them or open the disconnect before working on the array. Install everything per the National Electrical Code (NFPA 70) as adopted locally, including Article 690 for PV systems and Article 706 for storage. Check permit requirements with your building department, and hire a licensed electrician where your jurisdiction requires one, and for any connection to a building's existing wiring.
The master checklist
Print this, or keep it open while you shop. If a kit doesn't include an item, it goes on your separate shopping list.
| Part | Confirm before buying | Often missing from kits? |
|---|---|---|
| Panels | Voc, Isc, watts; matching specs | No |
| Mounting | Roof or ground type, tilt, sealing | Sometimes |
| Charge controller | MPPT; max PV voltage with cold headroom; output current; battery profile | Sometimes (or PWM substituted) |
| Battery bank | Usable Wh, chemistry, cold-charging limits, ventilation | Often |
| Inverter | Pure sine, continuous W, idle draw, input voltage | Often |
| Main battery fuse | Rating vs cable; interrupt rating | Very often |
| Branch fuses or breakers | One per circuit, rated to the cable | Very often |
| Disconnects | Battery, PV and inverter isolation | Very often |
| Cable and lugs | Gauge for current and ≤2.5% drop; correct lugs | Partly (short leads only) |
| Tools | Ratcheting crimper, PV connector tool, meter | Yes |
| Monitoring | Battery shunt monitor or controller app | Often |
Want to see what a typical "complete" kit actually ships with? Our hidden-costs guide breaks it down.
Frequently asked questions
Do I need an MPPT charge controller for a shed solar system?
For anything beyond a very small system, MPPT is the better choice. Victron Energy describes PWM as suitable for small systems only and says MPPT becomes worthwhile once array power passes a few hundred watts on a 12V battery. MPPT also lets you wire panels in series at higher voltage, which reduces cable size.
What fuses does an off-grid cabin solar system need?
At minimum, a main fuse in the battery positive cable and a fuse or breaker on each branch circuit, rated no higher than the cable can carry. The controller and array circuits also need protection as the manufacturers specify. Victron's Wiring Unlimited guide says a DC system should always include a main fuse.
Can I keep a LiFePO4 battery in an unheated shed?
Yes, but plan for winter. Standard LiFePO4 batteries shouldn't be charged below about 25°F without internal heating, according to Battle Born Batteries. Use a self-heating battery, an insulated battery enclosure, or limit winter charging. Avoid extreme heat as well.
Do I need a permit or an electrician for a cabin solar system?
It depends on your jurisdiction. The National Electrical Code covers PV systems in Article 690 and energy storage systems over 1 kWh in Article 706, and many areas adopt the NEC. Check with your local building department, and hire a licensed electrician where required, especially for any connection to existing building wiring.
What size wire should I use between panels, controller and battery?
Size each run for its current and length. Victron recommends aiming for no more than 2.5% voltage drop. Higher system voltage reduces current and cable size. Always check the cable's ampacity against its fuse rating, and use proper lugs crimped with a ratcheting tool.
Compare complete kits against this list
Our kit buying guide shows what popular kit types include and leave out, so you can price the full system before you buy.
Read the kit buying guide →Sources
- Wiring Unlimited — Victron Energy
- Which solar charge controller: PWM or MPPT? — Victron Energy
- NEC Article 690: Solar Photovoltaic Systems, Scope (690.1) — Mike Holt Enterprises
- NEC Article 706: Energy Storage Systems, Scope (706.1) — Mike Holt Enterprises
- Battery User's Guide — Trojan Battery Company
- Off-Grid or Stand-Alone Renewable Energy Systems — U.S. Department of Energy
This guide is for general information only and is not electrical, engineering or legal advice. Always follow the manufacturer's instructions, the National Electrical Code (NFPA 70) as adopted in your area, and local permitting rules, and hire a licensed electrician where your jurisdiction requires one. Product availability, specs and prices change; verify them on the listing before you buy. As an Amazon Associate we earn from qualifying purchases.