Guide
Will Snow Slide Off? Tilt and Mounting Choices for Snowy Sites
Whether snow slides off a panel depends less on luck than on four choices you make at install time: angle, clearance, frame and load rating.
Key takeaways
- In a year-long Michigan Tech study, elevated panels lost 5% to 12% of annual energy to snow, with the steepest tilt losing the least.
- In the same study, panels mounted at grade lost 29% to 34%, because snow that slid off piled up and blocked them. Ground clearance matters as much as angle.
- Sandia-led research on side-by-side arrays found frameless modules shed snow faster than framed ones.
- Datasheets list two kinds of load: test load and design load. Qcells lists a 5,400 Pa push design load against an 8,100 Pa test load for one module, so plan around the design figure.
- Load ratings only apply when the panel is clamped as its installation manual specifies.
The short answer
Snow slides off solar panels more readily when they are tilted steeply, mounted high enough that sliding snow has somewhere to go, and built without a raised frame lip at the lower edge. Field studies in Michigan, Ontario and Vermont point the same way.
The payoff can be large. Sandia National Laboratories notes that published estimates of annual snow losses range from 1 to 12 percent, with monthly losses as high as 100 percent in some cases. Mounting choices decide where your system lands in that range.
This guide is about design choices made before the snow falls. For removing snow that is already there, see our guide to safe snow-clearing tools.
What the research says about tilt
Michigan Tech: four angles, one snowy year
Researchers at Michigan Technological University mounted panels at 0°, 15°, 30° and 45° in Calumet, Michigan, and tracked them for a year starting in October 2013. That winter brought 5.3 meters (209 inches) of snow, which the authors describe as normal for the site.
For panels raised clear of the ground, annual snow losses ranged from 5% to 12%. The steepest tilt lost the least energy. The study was published in the IEEE Journal of Photovoltaics in 2015.
Ontario: losses fall as tilt rises
The Toronto and Region Conservation Authority's Sustainable Technologies Evaluation Program analyzed long-term output from arrays at different tilts and mounts. Its paper reports that snow losses decrease as tilt increases.
A 20° pole-mounted array shed snow much better than lower-tilt roof modules. The largest single-year loss, 10%, came from roof modules on a flat deck.
Why steeper works
Gravity pulls snow down the slope with more force as the angle rises, while friction on smooth glass changes little. Once the sun warms the panel through a thin snow layer, a thin melt film forms against the glass. On a steeper panel, that film is more likely to let the whole sheet slide.
The trade-off is summer output. A steep winter angle usually produces less in summer, when the sun is high. That is the main argument for an adjustable mount, covered below, and our comparison of fixed vs adjustable tilt mounts goes deeper on the year-round math.
Ground clearance: where does the snow go?
Angle alone is not enough. The Michigan Tech study also mounted panels at grade, with their lower edge near the ground. Those panels lost 29% to 34% of annual energy to snow, and tilt made little difference.
The authors describe this as a three- to sixfold increase in lost energy when ground interference is present. Snow that slid off had nowhere to go. It piled up at the lower edge, met the snowpack, and held the rest of the snow on the panel.
Plan for the pile. The lower edge of a ground mount should sit above the deepest snowpack you expect, plus the pile that sliding snow will add. Local snow depth records, or a neighbor who has lived through a few winters, are better guides than a rule of thumb.
The same logic applies to roofs. A low-slope roof array whose lower edge sits just above a parapet, or a panel mounted low on a wall above a deck, can trap its own snow. Pole mounts naturally avoid the problem, which may help explain why the Ontario pole array shed well.
Portrait or landscape?
The Michigan Tech panels were mounted in portrait orientation. The authors suggest that landscape layouts may help in snowy climates, depending on the inverter's voltage limits. How much it helps depends on how a panel's internal cell strings and bypass diodes are laid out, so ask the panel maker before rotating an array.
Framed vs frameless edges
Most panels have an aluminum frame whose edge stands slightly proud of the glass. That small lip can act as a dam for snow at the lower edge.
Sandia researchers, with partners including Michigan Tech, compared two otherwise identical arrays in Vermont, one with framed modules and one frameless. Their 2019 IEEE conference paper concluded that a frame inhibits performance in mild winter conditions.
A 2023 follow-up paper from the Sandia team restated that frameless modules shed snow faster than framed ones. It noted that the earlier finding rested on a single winter of data and added data from later winters.
The Ontario study saw the same mechanism from another angle. It attributed poor shedding on the flat-deck array partly to snow collecting along the bottom frame edge.
| Choice | Sheds better | Sheds worse | Evidence |
|---|---|---|---|
| Tilt angle | Steeper | Flatter | Michigan Tech 2015; TRCA STEP |
| Lower-edge clearance | Raised above snowpack | At grade or near an obstruction | Michigan Tech 2015 |
| Module edge | Frameless | Framed lip at bottom | Sandia et al. 2019, 2023; TRCA STEP |
| Mount style | Pole, elevated ground mount | Low-tilt roof on a flat deck | TRCA STEP |
| Orientation | Possibly landscape | Portrait, per the study setup | Michigan Tech 2015 (suggestion only) |
Frameless modules are less common in small off-grid kits. If yours are framed, angle and clearance are the levers you control.
Reading snow load ratings in Pa
Shedding is about energy. Load rating is about survival. Snow that stays on a panel presses on the glass and frame, so the panel's rated load has to exceed what your site can pile on it.
Push and pull, test and design
Datasheets list load in pascals (Pa). "Push" or front load is snow pressing down. "Pull" or rear load is mostly wind suction.
Many datasheets give two pairs of numbers. Qcells' Q.TRON BLK M-G2+ datasheet lists a maximum test load of 8,100 Pa push and 3,600 Pa pull. It lists a maximum design load of 5,400 Pa (113 lb/ft²) push and 2,400 Pa (50 lb/ft²) pull.
Sharp's installation manual explains the relationship: its test load is calculated with a safety factor of 1.5 from the design load. Use the design load for planning. The test load is what the panel survived in a lab, with no margin left.
| Panel | Front (snow) load | Rear (wind) load | Type of figure |
|---|---|---|---|
| Qcells Q.TRON BLK M-G2+ | 5,400 Pa design; 8,100 Pa test | 2,400 Pa design; 3,600 Pa test | Datasheet, design and test listed separately |
| Renogy 100W 12V monocrystalline | 5,400 Pa | 2,400 Pa | Product page; does not say test or design |
When a listing gives one number without saying which kind, ask the seller or check the installation manual. If a listing gives no load rating at all, treat that as a gap to resolve before buying for a snowy site. Our guide to Amazon solar kit listing red flags covers other gaps to watch for.
Ratings depend on how you clamp
Load ratings assume the panel is mounted the way its manual specifies. The Qcells datasheet points to its installation manual for the push and pull loads and says installation instructions must be followed.
Sharp's manual says clamps must hold the module frame completely within their width. It also says its guaranty may be void if customer-selected frame clamps are improper or inadequate. The manual warns that extreme snow build-up can deform a module's frame.
The mount and the structure under it have their own limits. A panel rated for heavy snow is only as strong as the rack, roof or posts carrying it. Local building codes set snow loads for structures, so check with your building department before putting up a large ground mount.
Choosing an adjustable tilt mount
An adjustable tilt mount lets you steepen panels for winter and flatten them for summer. For snowy sites, it is the simplest way to get better shedding without giving up summer output.
When comparing mounts, check these specs on the maker's own page or manual:
- Angle range. Confirm the steepest setting is steep enough for your winter goal.
- Panel compatibility. Check the supported panel sizes and that the clamping points line up with your panel's manual.
- Rated loads. Look for snow and wind ratings for the mount itself. If none are listed, ask before buying for a snowy site.
- Material and hardware. Aluminum or galvanized steel with stainless fasteners resists winter corrosion.
- Anchoring. Ground mounts need ballast or anchors suited to frost-heave soil; roof tilt legs need proper flashing.
- Lower-edge height. Work out how high the bottom edge sits at the steepest setting, then compare it with your snowpack.
- Adjustment method. Pin or bolt adjustments you can change with gloves on are easier to use in November.
Steeper angles also catch more wind. If a mount's wind rating is unclear, that matters more at a winter setting than a summer one.
Setup checklist by mounting type
| Mount type | Shedding | What to check |
|---|---|---|
| Flush roof mount | Follows roof pitch; poor on low slopes | Clearance to gutters and parapets; safe clearing from the ground |
| Tilt legs on a roof | Better than flush on low slopes | Roof penetrations and flashing; wind rating at steeper angles |
| Ground mount | Good if raised; poor at grade | Lower-edge height vs snowpack plus slide pile; frost-heave anchoring |
| Pole mount | Strong, per the Ontario data | Pole size and footing; easy seasonal tilt changes |
| Portable or folding panel | Depends on how you prop it | Prop it steeply and off the ground; bring it in before heavy snow |
Remember that snow is only part of the winter story. Short days and a low sun cut output too, which our cold-weather performance guide covers.
Falling snow. A panel that sheds well drops its snow in one slide. Keep walkways, doors and parked cars out of the landing zone below steep or high arrays.
Frequently asked questions
What tilt angle helps snow slide off solar panels?
Steeper is better for shedding. In a Michigan Tech study of 0°, 15°, 30° and 45° tilts, the steepest elevated panel lost the least energy to snow. The trade-off is lower summer output, which an adjustable mount can solve.
How high off the ground should a ground-mounted panel be in snow country?
High enough that the lower edge stays above the snowpack plus the pile that sliding snow adds. Michigan Tech found panels at grade lost 29% to 34% of annual energy, versus 5% to 12% for elevated panels.
Do frameless solar panels shed snow better?
Research led by Sandia found frameless modules shed snow faster than framed ones in side-by-side arrays in Vermont. A raised frame lip at the lower edge can hold snow in place.
What does a 5,400 Pa snow load rating mean?
It is the front pressure the panel is rated to carry, equal to about 113 lb/ft² per Qcells' datasheet. Check whether it is a design load or a test load; Sharp says its test load includes a 1.5 safety factor over the design load.
Does the load rating apply no matter how I mount the panel?
No. Ratings assume mounting per the installation manual. Sharp's manual says clamps must hold the frame completely within their width, and improper clamps may void its guaranty.
Should I lay portable panels flat in winter?
Both the Michigan Tech and Ontario studies found snow losses fall as tilt increases, so flat is the weakest position for shedding. Prop portable panels at a steep angle and off the ground, or bring them in before heavy snow.
Sources
- Impact of snow and ground interference on photovoltaic electric system performance (Heidari, Gwamuri, Townsend, Pearce; IEEE Journal of Photovoltaics, 2015) — Michigan Technological University Digital Commons
- Simple Approach to Estimating PV System Snow Losses Applied to Long-term PV Generation Data Sets for Different Tilt Angles and Mounting Styles (Janssen et al.) — Sustainable Technologies Evaluation Program, Toronto and Region Conservation Authority
- Differences in Snow Shedding in Photovoltaic Systems with Framed and Frameless Modules (Riley, Burnham, Walker, Pearce; IEEE PVSC, 2019) — Michigan Technological University Digital Commons
- An Enhanced Snow-Shedding Model: The Module Frame as a Key Variable (Riley, Burnham, Dice, Braid; IEEE PVSC, 2023) — Michigan Technological University Digital Commons
- The Impact of Snow on PV Performance — Sandia National Laboratories
- Q.TRON BLK M-G2+ data sheet — Qcells (hosted by Solartown)
- SHARP Installation Manual for Photovoltaic Modules (SIM13E-004) — Sharp
- Renogy 100 Watt 12 Volt Monocrystalline Solar Panel — Renogy
This article contains affiliate links. As an Amazon Associate we earn from qualifying purchases.